HTML datasheet архив (поиск документации на электронные компоненты) Поиск даташита (1.687.043 компонентов)
Где искать

Datasheet: CV210-1PCB75 (WJ Communications)

 

Скачать: PDF   ZIP
WJ Communications

Document Outline

Specifications and information are subject to change without notice
WJ Communications, Inc
Phone 1-800-WJ1-4401
FAX: 408-577-6621
e-mail: sales@wj.com
Web site: www.wj..com
October 2003
CV210-1
Cellular-band Dual-Branch Downconverter
Product Information
The Communications Edge
TM
Product Features
High dynamic range downconverter
with integrated LO and IF amplifiers
Dual channels for diversity
+30 dBm Input IP3
+11.5 dBm Input P1dB
RF: 800 915 MHz
IF: 65 120 MHz
Single supply operation (+5 V)
6x6 mm 28-pin QFN package
Low-side LO configuration
Common footprint with other
PCS/UMTS/cellular versions
Product Description
The CV210-1 is a dual-channel high-linearity
downconverter designed to meet the demanding
performance, functionality, and cost goals of current and
next generation mobile infrastructure basestations. It
provides high dynamic range performance in a low profile
surface-mount leadless package that measures 6 x 6 mm
square.
It is ideally suited for high dynamic range receiver front
ends using diversity receive channels. Functionality
includes frequency conversion and IF amplification,
while an integrated LO driver amplifier powers the
passive mixer. The MCM is implemented with reliable
and mature GaAs MESFET and InGaP HBT technology.
Typical applications include frequency downconversion
used in CDMA/GSM/TDMA, CDMA2000, W-CDMA,
and EDGE 2.5G and 3G mobile base transceiver stations.
Functional Diagram
Top View
Specifications
1
Parameters
Units
Min
Typ
Max
Comments
RF Frequency Range
MHz
800
915
LO Frequency Range
MHz
680
850
IF Center Frequency Range
MHz
65
75
120
See note 2
% Bandwidth around IF center frequency
%
7.5
See note 3
SSB Conversion Gain
dB
8
10
12
Temp = 25 C
Gain Drift over Temp (-40 C to 85 C)
dB
-1.5
0.1
1.5
Referenced to +25 C
Input IP3
dBm
+25
+30
See note 4
Input IP2
dBm
+33
+36.5
See note 4
Input 1 dB Compression Point
dBm
+11.5
See note 4
Noise Figure
dB
11
See note 5
LO Input Drive Level
dBm
-2.5
0
+2.5
LO-RF Isolation
dB
20
P
LO
= 0 dBm
LO-IF Isolation
dB
35
P
LO
= 0 dBm
Branch-Branch Isolation
dB
56
Return Loss: RF Port
dB
15
Return Loss: LO Port
dB
20
Return Loss: IF Port
dB
16
Operating Supply Voltage
V
+5
Supply Current
mA
320
385
475
Thermal Resistance
C / W
27
Junction Temperature
C 160
See
note
6
1. Specifications when using the application specific circuit (shown on page 3) with a low side LO = 0 dBm in a downconverting application at 25
C.
2. IF matching components affect the center IF frequency. Proper component values for other IF center frequencies than shown can be provided by emailing to applications.engineering@wj.com.
3. The IF bandwidth of the converter is defined as 15% around any center frequency in its operating IF frequency range. The bandwidth is determined with external components. Specifications are valid around
the total 7.5% bandwidth. ie. with a center frequency of 80 MHz, the specifications are valid from 80 6 MHz.
4. Assumes the supply voltage = +5 V. IIP3 is measured with
f = 1 MHz with RF
in
= -5 dBm / tone.
5. Assumes LO injection noise is filtered at the thermal noise floor, -174 dBm/Hz, at the RF, IF, and Image frequencies.
6. The maximum junction temperature ensures a minimum MTBF rating of 1 million hours of usage.
Absolute Maximum Rating
Ordering Information
Parameters
Rating
Part No.
Description
Operating Case Temperature
-40 to +85
C
CV210-1
Cellular-band Dual-Branch Downconverter
Storage Temperature
-55 to +125 C
CV210-1PCB75
Fully-Assembled Application Board, IF = 75 MHz
DC Voltage
+5.5 V
Junction Temperature
+220 C
Operation of this device above any of these parameters may cause permanent damage.
1
2
3
4
5
6
7
21
20
19
18
17
16
15
28
27
26
25
24
23
22
8
9
10
11
12
13
14
IF Amp 2
IF Amp 1
LO Driver Amp
BIAS
GND
N/C
GND
LO
GND
N/C
N/C
GND
BIAS
GND
N/C
GND
N/C
GND
MIX
E
R
IF
/R
F
1
GND
A
MP
1
IN
P
U
T
GND
GND
GND
MIX
E
R
IF
/R
F
2
GND
GND
GND
RF/IF
RF/IF
AM
P2
IN
P
U
T
IF
1
OUT
P
U
T
IF
2
OUT
P
U
T
LPF
Specifications and information are subject to change without notice
WJ Communications, Inc
Phone 1-800-WJ1-4401
FAX: 408-577-6621
e-mail: sales@wj.com
Web site: www.wj..com
October 2003
CV210-1
Cellular-band Dual-Branch Downconverter
Product Information
The Communications Edge
TM
Device Architecture / Application Circuit Information
Typical Downconverter Performance Chain Analysis (Each Branch)
Cumulative Performance
Stage
Gain
(dB)
Input
P1dB
(dBm)
Input
IP3
(dBm)
NF
(dB)
Current
(mA)
Gain
(dB)
Input
P1dB
(dBm)
Input
IP3
(dBm)
NF
(dB)
LO Amp / MMIC Mixer
-9
11
30
9.3
85
-9
11
30
9.3
IF Amplifier
19
2
22
1.8
150
10
8
27.5
11
CV210-1
Cumulative Performance
385*
10
+8
+27.5
11
* The
2
nd
branch includes another mixer and IF amplifier, which increases the total current consumption
of the MCM to be 385 mA.
CV210-1: The application circuit can be broken up into three main
functions as denoted in the colored dotted areas above: RF/IF diplexing
(blue), IF amplifier matching (green), and dc biasing (purple). There are
various placeholders for chip components in the circuit schematic so that
a common PCB can be used for all WJ dual-branch converters. Further
details are given in the Application Note located on the website titled
"CV2xx Series - PWB Design Guidelines".
External Diplexer:
In a downconversion application, the incoming RF
signal impinges on the switching elements of the mixer; the interaction
with these switches produces a signal at the IF frequency. The two
signals (RF and IF) are directed to the appropriate ports by the external
diplexer. A six-element diplexer is used in the circuit implementation.
IF Amplifier Matching:
The IF amplifier requires matching
elements to optimize the performance of the amplifier to the desired
IF center frequency. Since IF bandwidths are typically on the order
of 5 to 10%, a simple two element matching network, in the form of
either a high-pass or low-pass filter structure, is sufficient to match
the MMIC IF amplifier over these narrow bandwidths. Proper
component values for other IF center frequencies can be provided by
emailing to applications.engineering@wj.com.
DC biasing:
DC bias must be provided for the LO and IF amplifiers
in the converter. R1 sets the operating current for the last stage of the
LO amplifier and is chosen to optimize the mixer LO drive level.
Proper RF chokes and bypass capacitors are chosen for proper
amplifier biasing at the intended frequency of operation. The "+5 V"
dc bias should be supplied directly from a voltage regulator.
Printed Circuit Board Material:
.014" FR-4, 4 layers, .062" total thickness
1
2
3
4
5
6
7
21
20
19
18
17
16
15
28
27
26
25
24
23
22
8
9
10
11
12
13
14
IF Amp 2
IF Amp 1
LO Driver Amp
BIAS
GND
N/C
GND
LO
GND
N/C
N/C
GND
BIAS
GND
N/C
GND
N/C
GND
MIX
E
R
IF
/R
F
1
GND
A
MP
1
IN
P
U
T
GND
GND
GND
MIX
E
R
IF
/R
F
2
GND
GND
GND
RF/IF
RF/IF
AM
P2
IN
P
U
T
IF
1
OUT
P
U
T
IF
2
OUT
P
U
T
LPF
Specifications and information are subject to change without notice
WJ Communications, Inc
Phone 1-800-WJ1-4401
FAX: 408-577-6621
e-mail: sales@wj.com
Web site: www.wj..com
October 2003
CV210-1
Cellular-band Dual-Branch Downconverter
Product Information
The Communications Edge
TM
Application Circuit: IF = 75 MHz (CV210-1PCB75)
PCB Layout
Circuit Board Material: .014" FR-4, 4 layers, .062" total thickness
Bill of Materials
Ref. Desig.
Component
Size
R1
11.3
chip resistor
0805
R2, R3, R4, L10
L11, C16, C17
0
chip resistor
0603
R6, R7
3.3
chip resistor
0603
C1, C5, C10, C15
1000 pF chip capacitor
0603
C2, C8
3.9 pF chip capacitor
0603
C3, C9
8.2 pF chip capacitor
0603
C4, C11
22 pF chip capacitor
0603
C6, C12, C14
.01
F chip capacitor
0603
C7, C13
100 pF chip capacitor
0603
L1
120 nH chip inductor
0603
L2, L6
12 nH chip inductor
0603
L3, L7
22 nH chip inductor
0603
L4, L8
150 nH chip inductor
0603
L5, L9
220 nH chip inductor
0805
C19, C20, C21, C22 Do Not Place
U1
CV210-1 WJ Converter
QFN

Specifications and information are subject to change without notice
WJ Communications, Inc
Phone 1-800-WJ1-4401
FAX: 408-577-6621
e-mail: sales@wj.com
Web site: www.wj..com
October 2003
CV210-1
Cellular-band Dual-Branch Downconverter
Product Information
The Communications Edge
TM
CV210-1PCB75 Application Circuit Performance Plots
Conversion Gain vs IF Frequency
LO = 0 dBm, 740 MHz
7
8
9
10
11
12
65
70
75
80
85
IF Frequency (MHz)
Conversion Gain (dB)
-40 C
+25 C
+85 C
Input IP3 vs IF Frequency
LO = 0 dBm, 740 MHz
22
24
26
28
30
32
65
70
75
80
85
IF Frequency (MHz)
Input IP3 (dBm)
-40 C
+25 C
+85 C
Input IP2 vs IF Frequency
LO = 0 dBm, 740 MHz
30
32
34
36
38
40
65
70
75
80
85
IF Frequency (MHz)
Input IP2 (dBm)
-40 C
+25 C
+85 C
Conversion Gain vs RF Frequency
25 C, IF = 75 MHz, low-side LO
7
8
9
10
11
12
800
825
850
875
900
925
RF Frequency (MHz)
Conversion Gain (dB)
LO = -2.5 dBm
LO = 0 dBm
LO = 2.5 dBm
Input IP3 vs RF Frequency
25 C, IF = 75 MHz, low-side LO
22
24
26
28
30
32
800
825
850
875
900
925
RF Frequency (MHz)
Input IP3 (dBm)
LO = -2.5 dBm
LO = 0 dBm
LO = 2.5 dBm
Input IP2 vs RF Frequency
25 C, IF = 75 MHz, low-side LO
30
32
34
36
38
40
800
825
850
875
900
925
RF Frequency (MHz)
Input IP2 (dBm)
LO = -2.5 dBm
LO = 0 dBm
LO = 2.5 dBm
Conversion Gain vs RF Frequency
LO = 0 dBm, IF = 75 MHz, low-side LO
7
8
9
10
11
12
800
825
850
875
900
925
RF Frequency (MHz)
Conversion Gain (dB)
-40 C
+25 C
+85 C
Input IP3 vs RF Frequency
LO = 0 dBm, IF = 75 MHz, low-side LO
22
24
26
28
30
32
800
825
850
875
900
925
950
RF Frequency (MHz)
Input IP3 (dBm)
-40 C
+25 C
+85 C
Input IP2 vs RF Frequency
LO = 0 dBm, IF = 75 MHz, low-side LO
30
32
34
36
38
40
800
825
850
875
900
925
950
RF Frequency (MHz)
Input IP2 (dBm)
-40 C
+25 C
+85 C
Conversion Gain vs RF Frequency
25 C, LO = 0 dBm, IF = 75 MHz, low-side LO
7
8
9
10
11
12
800
825
850
875
900
925
RF Frequency (MHz)
Conversion Gain (dB)
Vdd = 4.9 V
Vdd = 5.0 V
Vdd = 5.1 V
Input IP3 vs RF Frequency
25 C, LO = 0 dBm, IF = 75 MHz, low-side LO
22
24
26
28
30
32
800
825
850
875
900
925
RF Frequency (MHz)
Input IP3 (dBm)
Vdd = 4.9 V
Vdd = 5.0 V
Vdd = 5.1 V
Input IP2 vs RF Frequency
25 C, LO = 0 dBm, IF = 75 MHz, low-side LO
30
32
34
36
38
40
800
825
850
875
900
925
RF Frequency (MHz)
Input IP2 (dBm)
Vdd = 4.9 V
Vdd = 5.0 V
Vdd = 5.1 V
Specifications and information are subject to change without notice
WJ Communications, Inc
Phone 1-800-WJ1-4401
FAX: 408-577-6621
e-mail: sales@wj.com
Web site: www.wj..com
October 2003
CV210-1
Cellular-band Dual-Branch Downconverter
Product Information
The Communications Edge
TM
CV210-1PCB75 Application Circuit Performance Plots (cont'd)
L-R Isolation vs LO Frequency
Referenced with LO = 0 dBm
0
5
10
15
20
25
30
35
650
700
750
800
850
900
LO Frequency (MHz)
L-R Isolation (dB)
-40 C
+25 C
+85 C
L-I Isolation vs LO Frequency
Referenced with LO = 0 dBm
15
20
25
30
35
40
650
700
750
800
850
900
LO Frequency (MHz)
L-I Isolation (dB)
-40 C
+25 C
+85 C
Branch-Branch Isolation vs RF Frequency
25 C
20
30
40
50
60
70
800
825
850
875
900
925
RF Frequency (MHz)
Isolation (dB)
IF Return Loss vs IF Frequency
25 C
0
5
10
15
20
25
30
65
70
75
80
85
IF Frequency (MHz)
Return Loss (dB)
RF Return Loss vs RF Frequency
25 C
0
5
10
15
20
25
30
800
825
850
875
900
925
RF Frequency (MHz)
Return Loss (dB)
LO Return Loss vs LO Frequency
25 C
0
5
10
15
20
25
30
700 725 750 775 800 825 850 875
LO Frequency (MHz)
Return Loss (dB)
Noise Figure vs Temperature
RF = 815 MHz, IF = 75 MHz, LO = 0 dBm @ 740 MHz
4
6
8
10
12
14
-40
-20
0
20
40
60
80
Temperature (C)
Noise Figure (dB)
Input P1dB vs Temperature
RF = 815 MHz, IF = 75 MHz, LO = 0 dBm @ 740 MHz
4
6
8
10
12
14
-40
-20
0
20
40
60
80
Temperature (C)
Input P1dB (dBm)
© 2020 • ChipFind
Контакты
Главная страница