HTML datasheet архив (поиск документации на электронные компоненты) Поиск даташита (1.687.043 компонентов)
Где искать

Datasheet: AH116-PCB880 (WJ Communications)

 

Скачать: PDF   ZIP
WJ Communications

Document Outline

This document contains information on a new product.
Specifications and information are subject to change without notice
WJ Communications, Inc
Phone 1-800-WJ1-4401
FAX: 408-577-6621
e-mail: sales@wj.com
Web site: www.wj.com
April 2003
The Communications Edge
TM
AH116
Watt, High Gain HBT Amplifier
Preliminary Product Information
Product Features
800 1000 MHz
+28 dBm P1dB
+42 dBm Output IP3
17 dB Gain
Single Positive Supply (+5 V)
MTBF >100 Years
SOIC-8 SMT Package
Product Description
The AH116 is a high dynamic range driver amplifier in a
low-cost surface mount package. The InGaP/GaAs HBT
is able to achieve high performance over a broad
frequency range with +42 dBm OIP3 and +28 dBm of
compressed 1-dB power and is housed in an industry
standard SOIC-8 SMT package. All devices are 100%
RF and DC tested.

The product is targeted for use as a driver amplifier for
wireless infrastructure where high linearity and medium
power is required. The internal active bias allows the
AH116 to maintain high linearity over temperature and
operate directly off a +5 V supply. This combination
makes the device an excellent fit for transceiver line
cards and power amplifiers in current and next generation
multi-carrier 3G base stations.



Functional Diagram






Function Pin
No.
Vref 1
Input
3
Output
6, 7
Vbias 8
GND Slug
N/C 2,
4,
5
Typical Specifications
Parameters
Units
Min
Typ
Max
Frequency Range
MHz
800
880
1000
S21 - Gain
dB
15.5
18
S11 - Input R.L.
dB
-15
S22 - Output R.L.
dB
-8
Output
P1dB
dBm +28
Output IP3
2
dBm +42
Noise Figure
dB
7.0
IS-95 Channel Power
@ -65 dBc ACPR, 9 Ch. Fwd
dBm +16
Operating Current Range
mA
200
250
300
Device
Voltage
V 5

Test conditions unless otherwise noted.
1. T = 25C, Vsupply = +5 V, Frequency = 880 MHz in recommended application circuit.
2. 3OIP measured with two tones at an output power of +13 dBm/tone separated by 1 MHz.
The suppression on the largest IM3 product is used to calculate the 3OIP using a 2:1 rule.



Absolute Maximum Rating
Ordering Information
Parameters
Rating
Part No.
Description
RF Input Power (continuous)
+20 dBm
AH116
Watt, High Linearity HBT Amplifier
DC Voltage / Current
+8 V / 400 mA
(Available in Tape & Reel)
DC Dissipation Power
2W
AH116-PCB880
Fully Assembled Evaluation Board, 900 MHz
Operation of this device above any of these parameters may cause permanent damage.



1
2

3
4
8
7
6
5
This document contains information on a new product.
Specifications and information are subject to change without notice
WJ Communications, Inc.
Phone 1-800-WJ1-4401
FAX: 408-577-6621
e-mail: sales@wj.com
Web site: www.wj.com
April 2003
The Communications Edge
TM
AH116
Watt, High Gain HBT Amplifier
Preliminary Product Information
880 MHz Application Circuit
500
1000
1500
Frequency (MHz)
Performance
-40
-30
-20
-10
0
10
20
(d
B
)

Typical Performance






Application Circuit PC Board Layout
Circuit Board Material: .014" FR-4, 4 layers (others added for rigidity), .062" total thickness, 1 oz copper
Frequency 880
MHz
S21 - Gain
18 dB
S11 -15
dB
S22 -8
dB
Output P1dB 28 dBm
Output IP3
42 dBm
DC Bias
5V, 250mA
NOTES:
Install R4 for single supply voltage control. Remove R4 to adjust bias using V
REF
or
adjust bias by changing R1. Align C9 at point 11.
S11
S21
S22
RF IN
C2
22 pF
22 pF
C1
51
R3
L = 20
Z = 50
2, 4, 5
AH116
3
6
7
Z = 50
L = 5
4.7 pF - (8.5 pF)
RF OUT
C9
Z = 50
L = 20
100 pF
C3
33 nH
1000 pF
C5
1
100
R1
0
R4
8
L1
R2
22
VREF
VCC
10 pF
C6
1000 pF
C7
10 uF
C4
This document contains information on a new product.
Specifications and information are subject to change without notice
WJ Communications, Inc
Phone 1-800-WJ1-4401
FAX: 408-577-6621
e-mail: sales@wj.com
Web site: www.wj.com
April
2003
The Communications Edge
TM
AH116
Watt, High Gain HBT Amplifier
Preliminary Product Information
Outline Drawing













































Land Pattern




























Product Marking
The component will be marked with an "AH116"
designator with a four- or five-digit alphanumeric lot
code on the top surface of the package. Tape and reel
specifications for this part is located on the website in
the "Application Notes" section.






















ESD / MSL Information
ESD Classification: Class 1B
Value: Passes
at
1000V
Test:
Human Body Model (HBM)
Standard:
JEDEC Standard JESD22-A114

MSL Rating:
Level 2
Standard:
JEDEC Standard J-STD-020A






Mounting Config. Notes
1. Ground / thermal vias are critical for the proper
performance of this device. Vias should use a .35mm
(#80 / .0135") diameter drill and have a final plated
thru diameter of .25 mm (.010").
2. Add as much copper as possible to inner and outer
layers near the part to ensure optimal thermal
performance.
3. Mounting screws can be added near the part to fasten
the board to a heatsink. Ensure that the ground /
thermal via region contacts the heatsink.
4. Do not put solder mask on the backside of the PC
board in the region where the board contacts the
heatsink.
5. RF trace width depends upon the PC board material
and construction.
6. Use 1 oz. Copper minimum.
7. All dimensions are in millimeters (inches). Angles
are in degrees.


This document contains information on a new product.
Specifications and information are subject to change without notice
WJ Communications, Inc
Phone 1-800-WJ1-4401
FAX: 408-577-6621
e-mail: sales@wj.com
Web site: www.wj.com
April
2003
The Communications Edge
TM
AH116
Watt, High Gain HBT Amplifier
Preliminary Product Information
Typical Device Data
S-Parameters (V
D
= +5 V, I
D
= 250 mA, T = 25
C, calibrated to device leads)
Freq (MHz)
S11 (dB)
S21 (dB)
S21 (ang)
S12 (dB)
S12 (ang)
S22 (dB)
S22 (ang)
50 -2.72
24.16
133.35
-36.72
29.75
-2.23
-102.97
100 -2.25 20.33
124.95
-35.31
13.96 -3.08
-137.03
200 -2.31 17.23
119.37
-34.90 2.32 -3.32
-159.63
300 -2.63 16.23
109.23
-34.22 -7.29 -3.30
-168.57
400 -3.08 15.63 98.28 -33.62 -16.36 -3.48 -172.70
500 -3.99 15.42 85.62 -33.01 -27.30 -3.14 -174.26
600 -5.79 15.58 69.70 -32.10 -37.73 -2.87 -176.25
700 -9.55 15.67 49.65 -31.23 -58.55 -2.69 -178.40
800 -19.72 15.22 25.60 -31.19 -78.95 -2.27 -179.74
900 -12.00 13.95 0.36 -32.11
-103.80 -1.66 177.95
1000 -6.06 11.91 -22.67 -33.26
-129.67 -1.40 173.15
1100 -3.59 9.46 -41.25 -35.51
-153.55 -1.42 168.43
1200 -2.34 6.92 -56.59 -38.16
176.95 -1.49 165.12
1300 -1.64 4.56 -68.13 -39.28
161.81 -1.71 163.09
1400 -1.28 2.28 -78.59 -41.14
132.98 -1.96 160.84
1500 -1.06 0.49 -88.03 -40.57
126.72 -2.27 162.34
1600 -0.91 -1.17 -96.56 -42.62
113.65 -2.53 160.80
1700 -0.77 -2.82
-105.47
-41.90 95.09 -2.76 158.88
1800 -0.71 -4.40
-112.20
-40.78 98.57 -2.92 157.57
1900 -0.65 -5.44
-118.80
-40.43 79.36 -3.11 156.96
2000 -0.60 -6.78
-128.36
-40.27 74.44 -3.29 155.77
2100 -0.55 -7.67
-139.22
-39.29 71.89 -3.55 155.05
2200 -0.58 -8.70
-146.80
-37.79 53.03 -3.72 155.24
2300 -0.56 -9.29
-158.26
-38.86 56.76 -3.90 155.59
2400 -0.55 -9.87
-169.80
-39.90 53.88 -3.96 158.19
2500 -0.54 -10.32 176.24 -37.63 53.78 -3.63 160.31
2600 -0.51 -10.59 160.74 -37.66 41.18 -3.25 160.80
2700 -0.52 -11.19 145.13 -37.20 48.65 -2.59 160.37
2800 -0.51 -11.66 128.82 -35.78 31.88 -1.97 158.05
2900 -0.50 -12.28 111.46 -36.13 35.11 -1.48 154.48
3000 -0.54 -13.08 95.01 -35.88 27.61 -1.09 149.64


Thermal Information
Parameters
Rating
Operating Case Temperature
-40 to +85
C
Storage Temperature
-55 to +150
C
Thermal Resistance
62
C/W
. To ensure MTTF > 1x10e6 hrs.

© 2020 • ChipFind
Контакты
Главная страница