HTML datasheet архив (поиск документации на электронные компоненты) Поиск даташита (1.687.043 компонентов)
Где искать

Datasheet: 050-000-0030070 (ITT Industries)

12-POINT CENTER PIN CRIMP TOOL

 

Скачать: PDF   ZIP
 
12-POINT CENTER PIN
CRIMP TOOL
GENERAL INFORMATION
Part number of the tool refers to both the positioner
and the tool frame as a combined unit.
The tool has a double action ratchet. Note that the
tool cannot be opened without completing the
crimp cycle.
SPECIFICATIONS
CRIMPING INSTRUCTIONS
1. With the tool in the open position, insert the contact
and the prepared wire through the indenter opening
and into the positioner.
2. Squeeze the handles together until the ratchet
releases. The handles will return to the open position.
Remove the crimped contact and wire.
ITT Industries
DATASHEET
THIS HAND TOOL MUST NOT BE USED IN ANY POWERED
"PRESS AS DEFINED BY OSHA CFR 1910.211 (46).
SEE REVERSE SIDE FOR IMPORTANT INFORMATION
CONCERNING REPAIR AND CALIBRATION INFORMATION.
FIXED
POSITIONER
CONTACT AND WIRE ENTER HERE
TOOL NO. 050-000-0030070
TOOL IN OPEN
POSTION
TOOL IN CLOSED
POSTION
DATAPLATE
GAGING INSTRUCTIONS
CAUTION!
"GO GAGING"
Operate the tool to the fully closed position. Maintain firm hand
pressure on the tool handles. Insert the "GO" gage end as shown.
The gage must pass freely between the indenter tips.
INDENTER
Operate the tool to the fully closed position. Maintain firm hand
pressure on the tool handles. Try to insert the "NO-GO" gage end as
shown. The "NO-GO" gage may partially enter the indenter opening,
but must not pass completely through the opening.
INDENTER
RED
GREEN
GREEN "GO"
RED "NO-GO"
DO NOT CRIMP GAGE!
"NO-GO GAGING"
050-000-0030073
ITT INDUSTRIES, 100 SEBETHE DRIVE, CROMWELL, CT 06416 PHONE 860/635-1500 FAX 860/635-2010
COPYRIGHT 2000 ITT INDUSTRIES, USA ALL RIGHTS RESERVED
12/00 REV. A
FILE # DS0148 DOC # AFMSP-76-DS
CARE OF TOOL
There is virtually no maintenance required. However, it is a good practice to keep indenter tips free of residual color
band deposits and other debris. A small wire brush may be used for this purpose.
We strongly recommend that you:
1. DO NOT immerse tools in cleaning solution.
2. DO NOT spray oil into tool to lubricate.
3. DO NOT attempt to disassemble tool or make repairs.
This is a precision hand crimp tool and should be handled as such.
The 12-point Center Pin Crimp Tool comes precalibrated from Daniels Manufacturing Corporation. The tool design was
based on specification M22520/2-01 for military hand tools. The hand tool is extremely rugged and the indenters are
made of hardened steel. The hand force required to cycle the tool is factory preset.
It is recommended that the indenters be periodically inspected and checked with a GO/NO-GO gage (P/N 050-000-
0030073). The inspection frequency should be based upon the amount of use, working conditions, operator training,
skill and established company standards. A recommended practice is to check the indenter gaging prior to each days
usage.
Should you require the Crimp Tool to be inspected annually, Daniels Manufacturing Corp. (DMC) has offered to inspect
and check the calibration of their hand tool for $50.00* per tool. The hand tool would be returned with a calibration label
certifying the day it was calibrated and inspected. The service center address is:
DANIELS MANUFACTURING CORP.
526 THORPE ROAD
ORLANDO, FL 32824
Phone: (407) 855-6161
Fax: (407) 855-6884
Web site: www.dmctools.com
e-mail: dmc@dmctools.com
* Pricing subject to change.
ITT Industries
DATASHEET
© 2017 • ChipFind
Контакты
Главная страница