HTML datasheet архив (поиск документации на электронные компоненты) Поиск даташита (1.687.043 компонентов)
Где искать

Datasheet: V23809-F7-T10 (Infineon Technologies AG)

Multimode 1300 Nm Led Fibre Channel 266 Mbd 1x9 Transceiver With St Connector

 

Скачать: PDF   ZIP
Infineon Technologies AG

Document Outline

Fiber Optics
JULY 1999
V23809-F7-T10
Multimode 1300 nm LED Fibre Channel
266 MBd 1x9 Transceiver with ST
Connector
FEATURES
Compliant with Fibre Channel standard
Meets mezzanine standard height of 9.8 mm
Compact integrated transceiver unit with duplex ST
receptacle
Single power supply with 3.0 V to 5.5 V range
Extremely low power consumption < 0.7 W at 3.3 V
PECL differential inputs and outputs
System is optimized for 62.5/50
m graded index fiber
Industry standard multisource footprint
Very low profile for high slot density
Testboard available
UL-94 V-0 certified
APPLICATIONS
FC fabric point-to-point links
HIPPI, SCSI, IPI
High speed computer links
Local area networks
High definition digital television
Switching systems
ST
is a registered trademark of AT&T
Absolute Maximum Ratings
Exceeding any one of these values may destroy the device
immediately.
Supply Voltage (V
CC
V
EE
) .......................................... 0.5 to 7 V
Data Input Levels (PECL) (V
IN
) .................................. V
EE
to V
CC
Differential Data Input Voltage (
V
IN
)..................................... 3 V
Operating Ambient Temperature (T
AMB
).............. 0
C to 85
C
Storage Ambient Temperature (T
STG
).................. 40
C to 85
C
Humidity/Temperature Test Condition (R
H
)................. 85%/85
C
Soldering Conditions, Temp/Time (T
SOLD
/t
SOLD
)
(MIL-STD 883C, Method 2003) .............................. 270
C/10 s
ESD Resistance (all pins to V
EE
, human body) .................. 1.5 kV
Output Current (I
O
) ........................................................... 50 mA
(0.3) .012 x .012
(14.4) .567
(9.8) max.
.39 max.
(41.2) 1.622
(3.8) .15 max.
(2.8)
max.
.11
max.
(18.47) .727
(20.32) .8
(5.27) .207
(1) .039
(0.6)
.024
(3
0.2
)
.118
.008
A
(1.4)
.055
2x
(0.1)
M A M
bottom
view
(0.3)
M A M
(1.4)
(25.4) max.
1 max.
(20.32)
8
(2.54)
.1
(12.7)
.5
x 9
1
9
Dimensions in (mm) inches
V23809-F7
-T1
0
FC-266 MBd-TRX
Fiber Optics
V23809-F7T10, MM 1300 nm LED Fibre Channel 1x9 Transceiver (ST)
2
DESCRIPTION
This data sheet describes the Infineon Fibre Channel trans-
ceiver, which belongs to the Infineon Multistandard Transceiver
Family. It is fully compliant with the Fibre Channel FC-133
MBaud and FC-266 MBaud standard.
Fibre Channel provides a general transport for upper layer proto-
cols such as Intelligent Peripheral Interface (IPI), High Perfor-
mance Parallel Interface (HIPPI) and Small Computer System
Interface (SCSI) command sets. Defined transmission rates are
266 MBaud and 133 MBaud in point-to-point or fabric topology.
The Infineon low cost multistandard transceiver is a single unit
comprised of a transmitter, a receiver, and an ST receptacle.
This design frees the customer from many alignment and PC
board layout concerns. The modules are designed for low cost
applications.
The inputs/outputs are PECL compatible, and the unit operates
from a 3.0 V to 5.5 V power supply. As an option, the data output
stages can be switched to static levels during absence of light
as indicated by the Signal Detect function. It can be directly in-
terfaced with available chipsets.
Regulatory Compliance
TECHNICAL DATA
The electro-optical characteristics described in the following
tables are valid only for use under the recommended operating
conditions.
Recommended Operating Conditions
Notes
1. For
V
CC
V
EE
(min., max.). 50% duty cycle. The supply current
(I
CC2
+I
CC3
) does not include the load drive current (ICC1). Add max.
45 mA for the three outputs. Load is 50
to V
CC
2 V.
2. To maintain good LED reliability, the device should not be held in the
ON state for more than the specified time. Normal operation should
be done with 50% duty cycle.
3. To achieve proper PECL output levels the 50
termination should
be done to V
CC
2 V. For correct termination see the application
notes.
Feature
Standard
Comments
Electromagnetic
Interference (EMI)
FCC Class B
EN 55022 Class B
CISPR 22
Noise frequency
range: 30 MHz to
1 GHz
Immunity:
Electrostatic
Discharge
EN 61000-4-2
IEC 1000-4-2
Discharges of
15kV with an air
discharge probe on
the receptacle cause
no damage.
Immunity:
Radio Frequency
Electromagnetic
Field
EN 61000-4-3
IEC 1000-4-3
With a field strength
of 10 V/m rms, noise
frequency ranges
from 10 MHz to
1 GHz
Eye Safety
IEC 825-1
Class 1
Parameter
Symbol
Min.
Typ. Max.
Units
Ambient Temperature
T
AMB
0
70
C
Power Supply Voltage V
CC
V
EE
3
5.5
V
Supply Current 3.3 V
I
CC
230
mA
Supply Current 5 V
(1)
260
Transmitter
Data Input
High Voltage
V
IH
V
CC
1165
880
mV
Data Input
Low Voltage
V
IL
V
CC
1810
1475
Threshold Voltage
V
BB
V
CC
1380
1260
Input Data Rise/Fall
Time, 20%80%
t
R
, t
F
0.4
1.3
ns
Data High Time
(2)
t
ON
1000
Receiver
Output Current
I
O
25
mA
Input Duty Cycle
Distortion
t
DCD
1
ns
Input Data
Dependent Jitter
t
DDJ
1
Input Random Jitter
t
RJ
0.76
Input Center
Wavelength
C
1260
1380
nm
Electrical
Output Load
(3)
R
L
50
Fiber Optics
V23809-F7T10, MM 1300 nm LED Fibre Channel 1x9 Transceiver (ST)
3
Transmitter Electro-Optical Characteristics
Notes
1. Measured at the end of 5 meters of 62.5/125/0.275 graded index
fiber using calibrated power meter and a precision test ferrule.
Cladding modes are removed. Values valid for EOL.
2. The input data pattern is a 12.5 MHz square wave pattern.
3. Center wavelength is defined as the midpoint between the two
50% levels of the optical spectrum of the LED.
4. Spectral width (full width, half max.) is defined as the difference
between 50% levels of the optical spectrum of the LED.
5. 10% to 90% levels. Measured using a 12.5 MHz square wave pat-
tern with an optoelectronic measurement system (detector and
oscilloscope) with 3 dB bandwidth ranging from less than 0.1 MHz
to more than 750 MHz.
6. Extinction ratio is defined as PL/PH x 100%. Measurement system
as in Note 5.
7. Test method and consideration as in FC-PH Appendix A.
8. Measured with the K28.5 pattern from Chapter II of the FC-PH at
266 MBd.
9. Measured with the K28.7 pattern from Chapter II of the FC-PH
which equals a 133 MHz square wave.
Receiver Electro-Optical Characteristics
Notes
1. Pattern: Manchester coding / NRZI (no scrambling)
2. For a bit error rate (BER) of less than 1x10E-12 over a receiver eye
opening of least 1.0 ns. Measured with a 2
7
1 PRBS.
3. For a BER of less than 1x10E-12. Measured in the center of the eye
opening with a 2
7
1 PRBS.
4. Test method and considerations as in FH-PC Appendix A.
5. Measured with the K28.5 pattern from Chapter II of the FC-PH at
266 MBd.
6. Measured with the K28.7 pattern from Chapter II of the FC-PH
which equals a 133 MHz square wave.
7. An increase in optical power through the specified level will cause
the Signal Detect output to switch from a Low state to a High state.
8. A decrease in optical power through the specified level will cause
the Signal Detect output to switch from a High state to a Low state.
9. PECL compatible. Load is 50
into V
CC
2 V. Measured under DC
conditions. For dynamic measurements a tolerance of 50 mV should
be added for V
CC
=5 V.
Transmitter Symbol Min.
Typ.
Max. Units
Data Rate
DR
0
266
MBaud
Launched Power
(Average)
(1, 2)
into 62.5
m Fiber
P
O
20
16
14
dBm
Center Wavelength
(2, 3)
C
1280
1380 nm
Spectral Width
(FWHM)
(2, 4)
l
200
Output Rise Time,
10%90%
(5)
t
R
0.6
2.0
ns
Output Rise Time,
10%90%
(5)
t
F
2.2
Temperature Coefficient
of Optical Output Power
TCp
0.03
dB/
C
Extinction Ratio
(Dynamic)
(2, 6)
ER
12
%
Deterministic Jitter
(7, 8)
t
DJ
16
Random Jitter
(7, 9)
t
RJ
9
Receiver
Symbol
Min.
Typ.
Max.
Units
Data Rate
DR
5
(1)
266
MBaud
Sensitivity
(Average Power)
(2)
P
IN
30
26
dBm
Saturation
(Average Power)
(3)
P
SAT
14
11
Deterministic
Jitter
(4, 5)
t
DJ
19
%
Random Jitter
(4, 6)
t
RJ
9
Signal Detect
Assert Level
(7)
P
SDA
43.5
29
dBm
Signal Detect
Deassert Level
(8)
P
SDD
45
30.5
Signal Detect
Hysteresis
P
SDA
P
SDD
1.5
dB
Output Low
Voltage
(9)
V
OL
V
CC
1810
1620 mV
Output High
Voltage
(9)
V
OH
V
CC
1025
880
Output Data Rise/Fall
Time, 20%80%
t
R
, t
F
1.3
ns
Output SD Rise/Fall
Time, 20%80%
40
Fiber Optics
V23809-F7T10, MM 1300 nm LED Fibre Channel 1x9 Transceiver (ST)
4
Pin Description
APPLICATION NOTE
Multimode 1300 nm Fibre Channel 1x9 Transceiver
The power supply filtering is required for good EMI perfor-
mance. Use short tracks from the inductor L1/L2 to the module
V
CC
Rx/V
CC
Tx.
A GND plane under the module is recommended for good EMI
and sensitivity performance.
Pin Name
Level
Pin #
Description
RxV
EE
Rx Ground
Power Supply
1
Negative power supply, normally ground
RxD
Rx Output Data
PECL Output
2
Receiver output data
RxDn
Rx Output Data
PECL Output
3
Inverted receiver output data
Rx SD
RX Signal Detect
PECL Output
active high
4
A high level on this output shows that an optical signal
is applied to the optical input
RxV
CC
Rx +3.3 to 5 V
Power Supply
5
Positive power supply, +3.3 to 5 V
TxV
CC
Tx +3.3 to 5 V
Power Supply
6
Positive power supply, +3.3 to 5 V
TxDn
Tx Input Data
PECL Input
7
Inverted transmitter input data
TxD
Tx Input Data
PECL Input
8
Transmitter input data
TxV
EE
Tx Ground
Power Supply
9
Negative power supply, normally ground
Case
Support
Not Connected
S1/S2
Support stud, not connected
GND
C1
VCC
VCC
GND
C2
VCC Rx
L1
GND
C3
GND
C4
L2
VCC Tx
GND
GND
VCC-Tx
VCC-Rx
Transceiver
R3
R1
GND GND
VCC-Tx
GND GND
VCC-Rx
GND
9
1
R4
R2
R7
R5
R8
R6
R9
TxD
TxDn
RDn
SD
RD
DC coupling between ECL gates.
L1/2
= 15000 nH (L2 is optional)
C1/3
= 4700 nF (optional)
C2/4
= 4700 nF
R1/3/5/7
= 82
(5V), 100
(4V), 127
(3.3V)
R2/4/6/8
= 130
(5V), 100
(4V), 83
(3.3V)
R9
= 200
Infineon Technologies AG Fiber Optics Wernerwerkdamm 16 Berlin D-13623, Germany
Infineon Technologies, Corp. Optoelectronics Division 19000 Homestead Road Cupertino, CA 95014 USA
Siemens K.K. Fiber Optics Takanawa Park Tower 20-14, Higashi-Gotanda, 3-chome, Shinagawa-ku Tokyo 141, Japan
www.infineon.com/fiberoptics
APPLICATION NOTE FOR MULTIMODE 1300 NM LED TRANSCEIVER
Solutions for connecting a Infineon 3.3 V Fiber Optic Transceiver to a 5.0 V Framer-/Phy-Device.
Figure 1. Common GND
Figure 2. Common V
CC
Framer/Phy
Clock
Recovery
Infineon
Fiber
Optic
Transceiver
V
CC
V
CC
Data
In
Data
Out
SD
In
Rx
Out
Tx
In
SD
Out
50
0
83
50
0
68
12
7
18
0
V
CC
5.0 V
V
CC
3.3 V
100 nF
100 nF
Framer/Phy
Clock
Recovery
5V
Infineon
Fiber
Optic 3.3 V
Transceiver
V
CC
V
CC
SD
In
51
0
18
K
V
CC
5.0 V
V
CC
3.3 V
SD
Out
1
1
1.8 V
Zener-Diode 1.8 V
Framer/Phy
Clock
Recovery
5V
Infineon
Fiber
Optic 3.3 V
Transceiver
V
CC
V
CC
SD
83
39K
127
26K
V
CC
5.0 V
V
CC
3.3 V
SD
SD
Inputs and outputs are differential and should be
doubled. Signal Detect (SD) is single ended (if used).
Figure 1a. Circuitry for SD (Differential) and
Common GND
Figure 1b. Circuitry for SD (Single Ended)
and Common GND
Framer/Phy
Clock
Recovery
Infineon
Fiber
Optic
Transceiver
V
CC
V
CC
Data
In
Data
Out
SD
In
Rx
Out
Tx
In
SD
Out
V
CC
GND 5.0 V
GND 5.0 V
GND 3.3 V
GND 3.3 V
GND 3.3 V
20
0
82
83
1
2
7
13
0
Inputs and outputs are differential
and should be doubled. Signal
Detect (SD) is single ended.
© 2017 • ChipFind
Контакты
Главная страница