HTML datasheet архив (поиск документации на электронные компоненты) Поиск даташита (1.687.043 компонентов)
Где искать

Datasheet: V23806-A84-C5 (Infineon Technologies AG)

3.3v Single Mode 155mbd Atm 2x9 Transceiver With RX Monitor

 

Скачать: PDF   ZIP
Infineon Technologies AG

Document Outline

Fiber Optics
JANUARY 2000
3.3 V
V23806-A84-C5
Single Mode 155 MBd ATM/SDH/SONET 2x9 Transceiver
with Rx Monitor
FEATURES
Compliant with ATM, SONET OC-3, SDH STM-1
Compact integrated transceiver unit with
MQW laser diode transmitter
InGaAs PIN photodiode receiver
Duplex SC receptacle
Class 1 FDA and IEC laser safety compliant
FDA Accession No. 9520890-08
Single power supply (+3.3 V)
Signal detect indicator
PECL differential inputs and outputs
Process plug included
Wave solderable and washable with process
plug inserted
Analog Rx power monitor output
Industry multisource 2x9 footprint
For distances of up to 15 km on single mode fiber
Absolute Maximum Ratings
Exceeding any one of these values may destroy the device
immediately.
Package Power Dissipation
(1)
............................................ 1.5 W
Supply Voltage (V
CC
V
EE
) ...................................................... 6 V
Data Input Levels.......................................................... V
CC
+0.5
Differential Data Input Voltage ............................................ 2.5 V
Operating Case Temperature.................................. 0
C to 70
C
Storage Ambient Temperature ............................40
C to 85
C
Soldering Conditions Temp/Time
(MIL-STD 883 C Method 2003) ............................. 250
C/5.5s
Note
1. For
V
CC
V
EE
(min., max.). 50% duty cycle. The supply current does
not include the load drive current of the receiver output. Add max.
45 mA for the three outputs. Load is 50
to VCC 2 V.
(1.5
0.1
)
.06
.004
(8.6 max)
.338 max
(0.75
0.1
)
.030
.004
6.375
.251
Optical
Centerline
PC board
(11.5 max)
.453 max.
(2) .080
(0.73
0.1)
.028
.004
(
0.45
0.1)
.0175
.004
(25.4
0.1
)
1
.004
20.32
33.02
1.3
(15.88
0.5
)
.625
.020
(52 max)
2.048 max
2.54
.100
20x
2x
Z
18x
DUPLEX
SC
RECEPTACLE
View Z
(Lead cross section
and standoff size)
PC board
thickness
(1.4
-0.05
)
.055
-.002
A
12.7
(11 max)
.433 max
Rx
Tx
.500
Top view
123456789
18
17
1
6
1
5
14
13
12
1
1
1
0
qqqqqqqqq
qqqqqqqqq
M
M
0.2
.008
M
M
0.3
.012
(4
0.2
)
.158
.008
A
A
M
M
0.3
.012
A
A
(2.54
0.2
)
.100
.008
Dimensions in (mm) inches
Fiber Optics
V23806-A84-C5, SM 155 MBd ATM/SDH/SONET 2x9 Trx w/Rx Monitor, 3.3 V
2
DESCRIPTION
The Infineon single mode ATM transceiver complies with the
ATM Forum's Network Compatible ATM for Local Network
Applications
document and ANSI's Broadband ISDN -
Customer Installation Interfaces,
Physical Media Dependent
Specification
, T1.646-1995, Bellcore-SONET OC-3/IR-1 and
ITU-T G.957 STM-1/S.1.1.
ATM was developed to facilitate solutions in multimedia appli-
cations and real time transmission. The data rate is scalable,
and the ATM protocol is the basis of the broadband public net-
works being standardized in the International Telecommunica-
tions Union (ITU), the former International Telegraph and
Telephone Consultative Committee (CCITT). ATM can also be
used in local private applications.
This Infineon single mode ATM transceiver is a single unit com-
prised of a transmitter, a receiver, and an SC receptacle. This
design frees the customer from many alignment and PC board
layout concerns. The module is designed for low cost WAN
applications. It can be used as the network end device interface
in workstations, servers, and storage devices, and in a broad
range of network devices such as bridges, routers, and intelli-
gent hubs, and wide area ATM switches.
This transceiver operates at 155.52 Mbit/s from a single power
supply (+3.3 V). The differential data inputs, data outputs and
signal detect output are PECL compatible.
Functional Description
This transceiver is designed to transmit serial data via single
mode cable.
Functional Diagram
The receiver component converts the optical serial data into
PECL compatible electrical data (RxD and RxDn). The Signal
Detect (SD, active high) shows whether an optical signal is
present
(1)
.
This transceiver offers the advantage of an analog Rx power
monitor (RxPMON) that can prove and control link status,
including transmission distances and security of the connec-
tion. This output shows an analog voltage that is proportional to
the light input within the range of -20 dBm to -30 dBm.
The transmitter part converts electrical PECL compatible serial
data (TxD and TxDn) into optical serial data. It contains a laser
driver circuit that drives the modulation and bias current of the
laser diode. The currents are controlled by a power control cir-
cuit to guarantee constant output power of the laser over tem-
perature and aging.
The power control uses the output of the monitor PIN diode
(mechanically built into the laser coupling unit) as a controlling
signal, to prevent the laser power from exceeding the operating
limits.
The laser can be switched off with a high signal on the Trans-
mitter Disable pin (TxDIS). The TxPMon pin shows a voltage
reflecting the optical power output. The bias current is moni-
tored on the BIASMON pins. Both signals can be used to super-
vise the function of the module.
Aging control is possible using the bias monitor output (BIAS-
MON). The module has an integrated shutdown function that
switches the laser off in the event of an internal failure.
The transceiver contains a supervisory circuit to control the
power supply. This circuit generates an internal reset signal
whenever the supply voltage drops below the reset threshold.
It keeps the reset signal active for at least 15 milliseconds after
the voltage has risen above the reset threshold. During this
time the laser is inactive.
Note
1. We recommend to switch off the transmitter supply (V
CC
-Tx) if no
transmitter input data is applied.
Laser
Driver
Laser
Power
Control
Receiver
SD
RxPMon
TxD
RxD
RxDn
BIASMON-
BIASMON+
TxDn
Laser
Coupling Unit
RX
Coupling Unit
e/o
o/e
o/e
TxDIS
TxPMon
3k
3k
10
Single
Mode
Fiber
Automatic
Shut-Down
Fiber Optics
V23806-A84-C5, SM 155 MBd ATM/SDH/SONET 2x9 Trx w/Rx Monitor, 3.3 V
3
TECHNICAL DATA
The electro-optical characteristics described in the following
tables are valid only for use under the recommended operating
conditions.
Recommended Operating Conditions
Note
1. For
V
CC
V
EE
(min., max.). 50% duty cycle. The supply current does
not include the load drive current of the receiver output. Add max.
45 mA for the three outputs. Load is 50
to V
CC
2 V.
Transmitter Electro-Optical Characteristics
Notes
1. Transmitter meets ANSI T1E1.2, SONET OC-3, and ITU-T G.957
mask patterns.
2. Laser power is shut down if power supply is below V
TH
and
switched on if power supply is above V
TH
after t
RES
. The supervi-
sory circuit can be reset by switching TxDis from high to low.
Receiver Electro-Optical Characteristics
Notes
1. Minimum average optical power at which the BER is less than
1 x 10
-10
. Measured with a 2
23
-1 NRZ PRBS as recommended by
ANSI T1E1.2, SONET OC-3, and ITU-T G.957.
2. An increase in optical power of data signal above the specified level
will cause the SIGNAL DETECT to switch from a Low state to a High
state.
3. A decrease in optical power of data signal below the specified level
will cause the SIGNAL DETECT to switch from a High state to a Low
state.
4. PECL compatible. Load is 50
into V
CC
2 V. Measured under DC
conditions at 25
C. For dynamic measurements a tolerance of
50 mV should be added. V
CC
=+3.3 V.
Parameter
Symbol
Min.
Typ. Max.
Units
Case Temperature
T
C
0
70
C
Power Supply
Voltage
V
CC
V
EE
3.14
3.3
3.47
V
Supply
Current
(1)
I
CC
150
230
mA
Transmitter
Data Input High Voltage
V
IH
V
CC
1165
880
mV
Data Input Low Voltage
V
IL
V
CC
1810
1475
Input Data Rise/Fall Time,
10%90%
tR, tF
0.4
1.3
ns
TxDis Input High Voltage
V
TIH
2.0
V
TxDis Input Low Voltage
V
TIL
0.8
Receiver
Output Current
I
O
25
mA
Input Center Wavelength
C
1260
1360
nm
Transmitter
Symbol
Min.
Typ.
Max.
Units
Output Power (Average) P
O
15.0
11.0 8.0
dBm
Center Wavelength
C
1274
1356
nm
Spectral Width, RMS
l
2.5
Output Rise/Fall Time,
20%80%
t
R
,
t
F
0.4
ns
Extinction Ratio
(Dynamic)
ER
8.2
12
dB
Eye Diagram
(1)
ED
Reset Threshold
for TxV
CC
(2)
V
TH
2.85
2.93
3.0
V
Reset Active
Time Out
(2)
t
RES
15
22
35
ms
Receiver
Symbol
Min.
Typ. Max.
Units
Sensitivity
(Average Power)
(1)
P
IN
34
31
dBm
Saturation
(Average Power)
P
SAT
8.0
3.0
Signal Detect
Assert Level
(2)
P
SDA
38
34
Signal Detect
Deassert Level
(3)
P
SDD
44
40
Signal Detect
Hysteresis
P
SDA
P
SDD
2
dB
Signal Detect
Assert Time
t
ASS
1
ms
Signal Detect
Deassert Time
t
DAS
5
PECL Output
Low Voltage
(4)
V
OL
V
CC
1950
1630
mV
PECL Output
High Voltage
(4)
V
OH
V
CC
1025
735
Output Data, Rise/Fall
Time, 20%80%
t
R
, t
F
0.7
1
ns
Output SD,
Rise/Fall Time
40
Fiber Optics
V23806-A84-C5, SM 155 MBd ATM/SDH/SONET 2x9 Trx w/Rx Monitor, 3.3 V
4
Pin Description
Regulatory Compliance
Pin Name
Level
Pin#
Description
NC
14
Pin not connected
Bias Mon
Bias Monitor
Analog Voltage
Bias Mon
Bias Mon +
5
6
This output shows an analog voltage that is proportional to the laser bias
current. Use this output to check proper laser operation and for end of life
indications. Limit: Bias Current I
BIAS
<60 mA
I
BIAS
=
TxDis
Tx Disable/Enable
TTL-Input
7
A low signal switches the laser on.
A high signal switches the laser off.
RxPMon
Rx Power Monitor
Analog Voltage
8
This output shows an analog voltage that is proportional to the light input.
Output voltage RxPMon = 2.5 V 0.3 V at 20 dBm opt. input signal, and
RxPMon=0.25 V0.03 V at 30 dBm opt. input signal.
Source Resistance R
S
= 300 k
.
TxPMon
Tx Power Monitor
Analog Voltage
9
This output shows an analog voltage that is proportional to the light output.
This output can be used for laser safety functions.
Output Voltage Vmon = 1.2, Source Resistance R
S
= 100 k
TxV
EE
Tx Ground
Power Supply
10
Negative power supply, normally ground
TxD
Tx Input Data
PECL Input
11
Transmitter input data
TxDn
12
Inverted transmitter input data
TxV
CC
Tx +3.3 V
Power Supply
13
Positive power supply, +3.3 V
RxV
CC
Rx +3.3 V
Power Supply
14
SD
Rx Signal Detect
PECL Output
active high
15
A high level on this output shows that optical data is applied to the optical
input.
RxDn
Rx Output Data
PECL Output
16
Inverted receiver output data
RxD
17
Receiver output data
RxV
EE
Rx Ground
Power Supply
18
Negative power supply, normally ground
Stud Pin
Mech. Support
S1/2
Not connected
Feature
Standard
Comments
Electrostatic Discharge (ESD)
to the Electrical Pins
MIL-STD 883C
Method 3015.4
Class 1 (>1000 V)
Immunity:
Electrostatic Discharge (ESD) to the
Duplex SC Receptacle
EN 61000-4-2
IEC 61000-4-2
Discharges of
15kV with an air discharge probe on the receptacle cause no
damage.
Immunity:
Radio Frequency
Electromagnetic Field
EN 61000-4-3
IEC 61000-4-3
With a field strength of 3 V/m rms, noise frequency ranges from 10 MHz to
1 GHz. No effect on transceiver performance between the specification limits.
Emission:
Electromagnetic Interference (EMI)
FCC Class B
EN 55022 Class B
CISPR 22
Noise frequency range: 30 MHz to 1 GHz
3 k
3 k
10
U
10
Fiber Optics
V23806-A84-C5, SM 155 MBd ATM/SDH/SONET 2x9 Trx w/Rx Monitor, 3.3 V
5
EYE SAFETY
This laser based single mode transceiver is a Class 1 product. It
complies with IEC 60825-1 and FDA 21 CFR 1040.10 and
1040.11.
To meet laser safety requirements the transceiver shall be oper-
ated within the Absolute Maximum Ratings.
Caution
All adjustments have been made at the factory prior to ship-
ment of the devices. No maintenance or alteration to the
device is required.
Tampering with or modifying the performance of the device
will result in voided product warranty.
Note
Failure to adhere to the above restrictions could result in a modifica-
tion that is considered an act of "manufacturing," and will require,
under law, recertification of the modified product with the U.S. Food
and Drug Administration (ref. 21 CFR 1040.10 (i)).
Laser Data
Required Labels
Laser Emission
Wavelength
1300 nm
Total output power (as defined by IEC: 50 mm aperture
at 10 cm distance)
less than
2 mW
Total output power (as defined by FDA: 7 mm aperture
at 20 cm distance)
less than
180
W
Beam divergence
4
Class 1 Laser Product
IEC
Complies with 21 CFR
1040.10 and 1040.11
FDA
Indication of laser
aperture and beam
© 2017 • ChipFind
Контакты
Главная страница