HTML datasheet архив (поиск документации на электронные компоненты) Поиск даташита (1.687.043 компонентов)
Где искать

Datasheet: TDP2012-920-F2 (Cyntec Co., Ltd.)

Diplexer DCS/PCS

 

Скачать: PDF   ZIP
 
CYNTEC 0805 DIPLEXER DATA SHEET
MODEL Part Number : TDP-2012-920-F1
Version : 3.0
Specification Revision History
Rev Date
Contents
Note
V3 2005.09.12
Document
Establishment
PAGE 1 OF 8
TITLE :
The Engineering Spec. for TDP-2012-920-F1 DIPLEXER
DOCUMENT
NO.
CYNP-53-010
PAGE
REV.
V3
UNLESS OTHERWISE SPECIFIED
TOLERANCES ON
X =
X.X =
X.XX =
ANGLES
HOLE DIA.
SCALE
X
UNIT
X
APPROVED BY
Wang Kevin
RELEASED BY
Yu-Lin Liao
DESIGNED BY
Yu-Lin Liao
CHECKED BY
Steven-Tseng
THIS DRAWINGS AND SPECIFICATIONS ARE THE PROPERTY OF CYNTEC CO., LTD.
AND SHALL NOT BE REPRODUCED OR USED AS THE BASIS FOR THE
MANUFACTURE OR SALE OF APPARATUS OR DEVICES WITHOUT PERMISSION
CYNTEC CO., LTD.
TDP-2012-920-F1 THIN FILM DIPLEXER
1.
Feature:
1.
Ultra Low Profile Thin Film Diplexer
2.
Multi-Band Handset application
3.
Lead Free
2.
Part Number
TDP 2012
-- 920 --F1 --
XX
(1) (2) (3)
(4) (5)
Where (1)
TDP : Thin Film Diplexer
(2) Size :4 digits of number 2012 = 2.01.25 mm
(3) Frequency Band:920 =900 MHz and 2GHz
(4) Type : Refer to Table 3-1
(5) XX : Internal Code
3.
Specifications
3-1
Electrical Specification
Part Number
TDP-2012-920-F1
Nominal Characteristics Impedance
50
Low : 824~960 MHz
Pass Band
High : 1710~1990 MHz
Low : 0.85dB Max @ 824~960 MHz @ 25
1.15dB Max @ 824~960 MHz @ 85
High : 1.0dB Max @ 1710~1990 MHz @ 25
Insertion Loss
1.3dB Max @ 1710~1990 MHz @ 85
Low : 0.3dB Max
Ripple in BW
High : 0.3dB Max
Low :23dB Min @1648~1830 MHz
Low :22Db Min @2472~2745 MHz
Low :17dB Min @3296~3660 MHz
Low :17dB Min @4120~4575 MHz
High : 22dB Min @3420~3820 MHz
High : 25dB Min @5130~5730 MHz
Attenuation
High : 13dB Min @8550~9550 MHz
Low : 1.5 Max
VSWR in BW
High : 1.5 Max
PAGE 2 OF 8
TITLE :
The Engineering Spec. for TDP-2012-920-F1 DIPLEXER
DOCUMENT
NO.
CYNP-53-010
PAGE
REV.
V3
UNLESS OTHERWISE SPECIFIED
TOLERANCES ON
X =
X.X =
X.XX =
ANGLES
HOLE DIA.
SCALE
X
UNIT
X
APPROVED BY
Wang Kevin
RELEASED BY
Yu-Lin Liao
DESIGNED BY
Yu-Lin Liao
CHECKED BY
Steven-Tseng
THIS DRAWINGS AND SPECIFICATIONS ARE THE PROPERTY OF CYNTEC CO., LTD.
AND SHALL NOT BE REPRODUCED OR USED AS THE BASIS FOR THE
MANUFACTURE OR SALE OF APPARATUS OR DEVICES WITHOUT PERMISSION
CYNTEC CO., LTD.
4.
Outline Dimension
GND
Com
GND
GND
Unit : um
HB
LB
Typical Performance
* This data is measured under testing port connected to system impedance and another port kept open.

PAGE 3 OF 8
TITLE :
The Engineering Spec. for TDP-2012-920-F1 DIPLEXER
DOCUMENT
NO.
CYNP-53-010
PAGE
REV.
V3
UNLESS OTHERWISE SPECIFIED
TOLERANCES ON
X =
X.X =
X.XX =
ANGLES
HOLE DIA.
SCALE
X
UNIT
X
APPROVED BY
Wang Kevin
RELEASED BY
Yu-Lin Liao
DESIGNED BY
Yu-Lin Liao
CHECKED BY
Steven-Tseng
THIS DRAWINGS AND SPECIFICATIONS ARE THE PROPERTY OF CYNTEC CO., LTD.
AND SHALL NOT BE REPRODUCED OR USED AS THE BASIS FOR THE
MANUFACTURE OR SALE OF APPARATUS OR DEVICES WITHOUT PERMISSION
CYNTEC CO., LTD.
5.
Recommended Land Pattern















PAGE 4 OF 8
TITLE :
The Engineering Spec. for TDP-2012-920-F1 DIPLEXER
DOCUMENT
NO.
CYNP-53-010
PAGE
REV.
V3
UNLESS OTHERWISE SPECIFIED
TOLERANCES ON
X =
X.X =
X.XX =
ANGLES
HOLE DIA.
SCALE
X
UNIT
X
APPROVED BY
Wang Kevin
RELEASED BY
Yu-Lin Liao
DESIGNED BY
Yu-Lin Liao
CHECKED BY
Steven-Tseng
THIS DRAWINGS AND SPECIFICATIONS ARE THE PROPERTY OF CYNTEC CO., LTD.
AND SHALL NOT BE REPRODUCED OR USED AS THE BASIS FOR THE
MANUFACTURE OR SALE OF APPARATUS OR DEVICES WITHOUT PERMISSION
CYNTEC CO., LTD.
6.
Reliability Test
7.1 Electrical
ITEM
Specification and Requirement
Test Method
Temperature Characteristics Satisfy electrical characteristics
Solder the sample on PCB.
Exposure at each temperature,
-40, -20, 0, +25, +50,
+85 for 30minutes

7.2 Mechanical
ITEM
Specification and Requirement
Test Method
Solderability
The Surface of terminal immersed shall
be minimum of 95% covered with a new
coating of solder
Solder bath :
After immersing in flux, dip in245
+ 5 molten solder bath for 2 +
0.5 seconds
Resistance to solder Heat Satisfy electrical characteristics without
distinct deformation in appearance
A. Pre-heat : 100 ~ 110 for 30
seconds
B. Immersed at solder bath of 270
+ 5 for 20 + 1 seconds
Vibration
Satisfy electrical characteristics without
Mechanical damage such as break
Vibrate as apply 20 to 2,000Hz,
186m/s
2
(19G) acceleration 1.5mm
amplitude for 2 hours in each of
three (X, Y, Z) axis (total 6 hours).
Shock
Satisfy electrical characteristics without
mechanical damaged such as break
(1)
Break value : 490 N
(2)
Duration of pulse : 11ms
(3)
3 times in each positive and
negative direction of 3 mutual
perpendicular directions.
Bending Test
Satisfy electrical characteristics without
mechanical damage such as break
Bending value : 3mm for 30 + 1
seconds
Solvent Resistant
Marking should be legible without
mechanical and distinct damage in
appearance
(1)
Solvent : Trichloroethane or
Isopropyl alcohol.
(2)
Immersed in solvent at room
temperature for 90 seconds
Drop Test
Satisfy electrical characteristics without
mechanical damage
Drop the sample from a height of
1m to concrete ground for 10 times




PAGE 5 OF 8
TITLE :
The Engineering Spec. for TDP-2012-920-F1 DIPLEXER
DOCUMENT
NO.
CYNP-53-010
PAGE
REV.
V3
UNLESS OTHERWISE SPECIFIED
TOLERANCES ON
X =
X.X =
X.XX =
ANGLES
HOLE DIA.
SCALE
X
UNIT
X
APPROVED BY
Wang Kevin
RELEASED BY
Yu-Lin Liao
DESIGNED BY
Yu-Lin Liao
CHECKED BY
Steven-Tseng
THIS DRAWINGS AND SPECIFICATIONS ARE THE PROPERTY OF CYNTEC CO., LTD.
AND SHALL NOT BE REPRODUCED OR USED AS THE BASIS FOR THE
MANUFACTURE OR SALE OF APPARATUS OR DEVICES WITHOUT PERMISSION
CYNTEC CO., LTD.
© 2020 • ChipFind
Контакты
Главная страница