HTML datasheet архив (поиск документации на электронные компоненты) Поиск даташита (1.687.043 компонентов)
Где искать

Datasheet: TBF2520-190-B2 (Cyntec Co., Ltd.)

PHS (1893-1920MHz)

 

Скачать: PDF   ZIP
 
TBF-2520-190-B SERIES THIN FILM BAND PASS FILTER
1. Feature:
1. 1.90GHz Thin Film Band Pass Filter
2. Lead Free
2. Part Number
TBF 2520
-- 190 --B2
--
XX
(1) (2) (3)
(4) (5)
Where
(1) TBF : Thin Film Band Pass Filter
(2)
Size
:
4 digits of number 2520 = 2.502.00 mm
(3) Center Frequency :
190 = 1.906 GHz
(4)
Type
Refer to Table 3-1
(5)
XX
Internal Code

3. Ratings
3-1 Specifications
Part Number
TBF-2520-190-B2
Nominal Characteristics Impedance
50
Nominal Center Frequency
1906MHz
Bandwidth
1893 ~ 1920MHz
Insertion Loss
1.2 dB Max. at +25 deg. C
1.5 dB max. at 40 ~ +85 deg. C
Ripple in BW
0.5dB max.
Attenuation
35.0dB min. at 1420 MHz
15.0dB min. at 1660 MHz
3.0dB min. at 1798 MHz
6.0dB min. at 2126 MHz
25.0dB min. at 3814 MHz
25.0dB min. at 5721 MHz
VSWR in BW
2.0 Max.
Power Capacity
500mW Max.
3-2 Operation Temperature:
-40 to +85
3-3 Storage Temperature: +15 to +35
PAGE 1 OF 1
TITLE :
The Engineering Spec. for TBF-2520-190-B2 Band Pass Filter
DOCUMENT
NO.
PAGE
REV.
UNLESS OTHERWISE SPECIFIED
TOLERANCES ON
X =
X.X =
X.XX =
ANGLES
HOLE DIA.
SCALE
X
UNIT
X
APPROVED BY
RELEASED BY
DESIGNED BY
CHECKED BY
THIS DRAWINGS AND SPECIFICATIONS ARE THE PROPERTY OF CYNTEC CO., LTD.
AND SHALL NOT BE REPRODUCED OR USED AS THE BASIS FOR THE
MANUFACTURE OR SALE OF APPARATUS OR DEVICES WITHOUT PERMISSION
CYNTEC CO., LTD.

4. Outline Dimension
Code Dimension Code Dimension
L 2.5
+ 0.2
L1
2.0 + 0.1
W
2.0 + 0.2
Lt
1.2 + 0.1
T 0.5
+ 0.1 Lw 0.2 + 0.1
W1
0.8
+ 0.1
Wt
0.4
+ 0.1
Ww
0.2
+ 0.1
Unit : mm
Terminal Configuration:
Terminal No.
Terminal Name
(1) GND
(2) Output
(3) GND
(4) Input
5. Electrical Performance

PAGE 2 OF 2
TITLE :
The Engineering Spec. for TBF-2520-190-B2 Band Pass Filter
DOCUMENT
NO.
PAGE
REV.
UNLESS OTHERWISE SPECIFIED
TOLERANCES ON
X =
X.X =
X.XX =
ANGLES
HOLE DIA.
SCALE
X
UNIT
X
APPROVED BY
RELEASED BY
DESIGNED BY
CHECKED BY
THIS DRAWINGS AND SPECIFICATIONS ARE THE PROPERTY OF CYNTEC CO., LTD.
AND SHALL NOT BE REPRODUCED OR USED AS THE BASIS FOR THE
MANUFACTURE OR SALE OF APPARATUS OR DEVICES WITHOUT PERMISSION
CYNTEC CO., LTD.

6. Recommended Land Pattern
Line Width be designed to match 50ohm characteristic impedance, depending on
PCB material and thickness
Notes : All the technical data and information contained herein are subject to change
without prior notice





PAGE 3 OF 3
TITLE :
The Engineering Spec. for TBF-2520-190-B2 Band Pass Filter
DOCUMENT
NO.
PAGE
REV.
UNLESS OTHERWISE SPECIFIED
TOLERANCES ON
X =
X.X =
X.XX =
ANGLES
HOLE DIA.
SCALE
X
UNIT
X
APPROVED BY
RELEASED BY
DESIGNED BY
CHECKED BY
THIS DRAWINGS AND SPECIFICATIONS ARE THE PROPERTY OF CYNTEC CO., LTD.
AND SHALL NOT BE REPRODUCED OR USED AS THE BASIS FOR THE
MANUFACTURE OR SALE OF APPARATUS OR DEVICES WITHOUT PERMISSION
CYNTEC CO., LTD.


7. Reliability Test
7.1 Electrical
ITEM
Specification and Requirement
Test Method
Temperature Characteristics Satisfy electrical characteristics
Solder the sample on PCB.
Exposure at each temperature,
-40, -20, 0, +25, +50,
+85 for 30minutes

7.2 Mechanical
ITEM
Specification and Requirement
Test Method
Solderability
The Surface of terminal immersed shall
be minimum of 95% covered with a new
coating of solder
Solder bath :
After immersing in flux, dip in245
+ 5 molten solder bath for 2 +
0.5 seconds
Resistance to solder Heat Satisfy electrical characteristics without
distinct deformation in appearance
A. Pre-heat : 100 ~ 110 for 30
seconds
B. Immersed at solder bath of 270
+ 5 for 20 + 1 seconds
Vibration
Satisfy electrical characteristics without
Mechanical damage such as break
Vibrate as apply 20 to 2,000Hz,
186m/s
2
(19G) acceleration 1.5mm
amplitude for 2 hours in each of
three (X, Y, Z) axis (total 6 hours).
Shock
Satisfy electrical characteristics without
mechanical damaged such as break
(1) Break value : 490 N
(2) Duration of pulse : 11ms
(3) 3 times in each positive and
negative direction of 3 mutual
perpendicular directions.
Bending Test
Satisfy electrical characteristics without
mechanical damage such as break
Bending value : 3mm for 30 + 1
seconds
Solvent
Resistant
Marking should be legible without
mechanical and distinct damage in
appearance
(1) Solvent : Trichloroethane or
Isopropyl alcohol.
(2) Immersed in solvent at room
temperature for 90 seconds
Drop Test
Satisfy electrical characteristics without
mechanical damage
Solder the sample on PCB. Drop
the sample from a height of 1m to
concrete ground for 10 times

PAGE 4 OF 4
TITLE :
The Engineering Spec. for TBF-2520-190-B2 Band Pass Filter
DOCUMENT
NO.
PAGE
REV.
UNLESS OTHERWISE SPECIFIED
TOLERANCES ON
X =
X.X =
X.XX =
ANGLES
HOLE DIA.
SCALE
X
UNIT
X
APPROVED BY
RELEASED BY
DESIGNED BY
CHECKED BY
THIS DRAWINGS AND SPECIFICATIONS ARE THE PROPERTY OF CYNTEC CO., LTD.
AND SHALL NOT BE REPRODUCED OR USED AS THE BASIS FOR THE
MANUFACTURE OR SALE OF APPARATUS OR DEVICES WITHOUT PERMISSION
CYNTEC CO., LTD.


7.3 Load Life
ITEM
Specification and Requirement
Test Method
Rapid change of temperature Satisfy Electrical Characteristics.
Without distinct damage.
Perform 5 cycles as follows :
-55 for 30minutes room
temperature for 3 minutes
+125 for 30minutes room
temperature for 3 minutes.
(Dwell time : 5 to 8 minutes)
Humidity Resistance Test
Satisfy Electrical Characteristics.
Without distinct damage.
Precondition at +25 for 1hour.
Let stand at temperature +40
3
, 90~95% relative humidity for
1,000 hours before taking final
measurements.
Low Temperature Store
Satisfy Electrical Characteristics.
Without distinct damage.
Solder the sample on PCB.
Exposure at
-55 3 for 1,000
hours.
1~2 hours exposure at room
temperature and humidity, prior to
measurement.
High Temperature Store
Satisfy Electrical Characteristics.
Without distinct damage.
Solder the sample on PCB.
Exposure at +85
3 for 1,000
hours.
1~2 hours exposure at room
temperature and humidity, prior to
measurement.
Load Life
Satisfy Electrical Characteristics.
Without distinct damage.
Apply 16 Volt voltage at 702
ambient







PAGE 5 OF 5
TITLE :
The Engineering Spec. for TBF-2520-190-B2 Band Pass Filter
DOCUMENT
NO.
PAGE
REV.
UNLESS OTHERWISE SPECIFIED
TOLERANCES ON
X =
X.X =
X.XX =
ANGLES
HOLE DIA.
SCALE
X
UNIT
X
APPROVED BY
RELEASED BY
DESIGNED BY
CHECKED BY
THIS DRAWINGS AND SPECIFICATIONS ARE THE PROPERTY OF CYNTEC CO., LTD.
AND SHALL NOT BE REPRODUCED OR USED AS THE BASIS FOR THE
MANUFACTURE OR SALE OF APPARATUS OR DEVICES WITHOUT PERMISSION
CYNTEC CO., LTD.
© 2019 • ChipFind
Контакты
Главная страница