HTML datasheet архив (поиск документации на электронные компоненты) Поиск даташита (1.687.043 компонентов)
Где искать

Datasheet: 4P2R-0201x2 (Cyntec Co., Ltd.)

Isolated Resistor Network

 

Скачать: PDF   ZIP
 
PAGE 1 OF 9
TITLE :
The Engineering Spec. For RS062R-XXXX-X2N
DOCUMENT
NO.
CYNP-5X-001
PAGE
REV.
A0
UNLESS OTHERWISE SPECIFIED
TOLERANCES ON
X =
X.X =
X.XX =
ANGLES
HOLE DIA.
SCALE
X
UNIT
X
APPROVED BY
DRAWN BY
2005-10-04
DESIGNED BY
CHECKED BY
THIS DRAWINGS AND SPECIFICATIONS ARE THE PROPERTY OF CYNTEC CO., LTD.
AND SHALL NOT BE REPRODUCED OR USED AS THE BASIS FOR THE
MANUFACTURE OR SALE OF APPARATUS OR DEVICES WITHOUT PERMISSION
CYNTEC CO., LTD.
RS062R-XXXX-X2N Resistor Network
1. Scope
This specification applies to 0.
6mm x 0.
8mm size resistor ne
twork (4P2R) with
2 isolated
resistor for use in electronic equipment.
2. Type Designation
RS062R -- XXXX --
X 2 N
(1)
(2)
(3) (4) (5)
Where (1) Series No:
0.6mm x 0.8mm Size & 4 Pins 2 Resistors
(2) Nominal resistance value :
For example
56R0 = 56
1001 = 1k
(3) Resistance tolerance:
J = 5.0%
(4) Outline type:
2 = Flat type
(5) N = Sn plating (Lead free, RoHS compliant)
3. Electrical Specifications
Table 1. :
Power Rating*
31mW/each element
Resistance Values
10 to 1M in E-24 series
Resistance Tolerance
5.0% (J)
T.C.R.
(Temperature Coefficient of Resistance)
200ppm/
Operating Temperature Range
-55 to 125
Maximum Operating Voltage**
12.5V
PAGE 2 OF 9
TITLE :
The Engineering Spec. For RS062R-XXXX-X2N
DOCUMENT
NO.
CYNP-5X-001
PAGE
REV.
A0
UNLESS OTHERWISE SPECIFIED
TOLERANCES ON
X =
X.X =
X.XX =
ANGLES
HOLE DIA.
SCALE
X
UNIT
X
APPROVED BY
DRAWN BY
2005-10-04
DESIGNED BY
CHECKED BY
THIS DRAWINGS AND SPECIFICATIONS ARE THE PROPERTY OF CYNTEC CO., LTD.
AND SHALL NOT BE REPRODUCED OR USED AS THE BASIS FOR THE
MANUFACTURE OR SALE OF APPARATUS OR DEVICES WITHOUT PERMISSION
CYNTEC CO., LTD.
Note: *Package Power Temperature Derating Curve
AMBIENT TEMPERATURE(
)
0
-55
70
125
R
A
T
E
D

L
O
A
D
(
%
)
100
Figure 1.Power Temperature Derating Cure
Note: **Resistors shall have a rated DC or AC(rms.) continuous operating voltage corresponding
to the power rating, as calculated from the following formula
Where V
: Rated voltage (V)
P
: Rated power (W)
R
P
V
=
R
: Nominal resistance ()
If the voltage so obtained exceeds the maximum operating voltage, this maximum voltage shall
be the rated voltage.
4. Outline dimensions and marking
A1
L
P
W
C
D
T
5. Schematics
L
0.80 0.10
P
0.50 typical
W
0.60 0.10
C
0.15 0.10
A1
0.30 0.10
D
0.15 0.10
T
0.35 0.10
Unit: mm
R1
R2
R1=R2
PAGE 3 OF 9
TITLE :
The Engineering Spec. For RS062R-XXXX-X2N
DOCUMENT
NO.
CYNP-5X-001
PAGE
REV.
A0
UNLESS OTHERWISE SPECIFIED
TOLERANCES ON
X =
X.X =
X.XX =
ANGLES
HOLE DIA.
SCALE
X
UNIT
X
APPROVED BY
DRAWN BY
2005-10-04
DESIGNED BY
CHECKED BY
THIS DRAWINGS AND SPECIFICATIONS ARE THE PROPERTY OF CYNTEC CO., LTD.
AND SHALL NOT BE REPRODUCED OR USED AS THE BASIS FOR THE
MANUFACTURE OR SALE OF APPARATUS OR DEVICES WITHOUT PERMISSION
CYNTEC CO., LTD.
Figure 2 : Measurment Setup
Substrate Side
(R=0.5 mm)
Over coat Film
Measurement Point A
Pressure Rod
Substrate
(Metal)
Measurement Point B
Metal Block
Sample Electrode
Insulation Plate
B
A
Spring
Voltage Supply
6. Life test
6-1 Electrical
Item
Specification and Requirement
Test Method
Short Time Overload R: (2.0%+ 0.1)
Without damage by flashover, spark,
arcing, burning or breakdown
(1) Applied voltage :
2.5 x rated voltage or
2 x maximum operating voltage
which ever is less
(2) Test time : 5 seconds
Insulation Resistance Over 100 M on Overcoat layer face up
Over 1,000 M on Substrate side face up
(1) Setup as figure 2
(2) Test voltage : 100 V
DC
(3) Test time :
60 + 10 / -0 seconds
Voltage Proof
R: (1.0%+ 0.05)
Without damage by flashover, spark,
arcing, burning or breakdown
(1) Setup as figure 2
(2) Test voltage : 100 V
AC
(rms.)
(3) Test time:
60 +10 / -0 seconds
PAGE 4 OF 9
TITLE :
The Engineering Spec. For RS062R-XXXX-X2N
DOCUMENT
NO.
CYNP-5X-001
PAGE
REV.
A0
UNLESS OTHERWISE SPECIFIED
TOLERANCES ON
X =
X.X =
X.XX =
ANGLES
HOLE DIA.
SCALE
X
UNIT
X
APPROVED BY
DRAWN BY
2005-10-04
DESIGNED BY
CHECKED BY
THIS DRAWINGS AND SPECIFICATIONS ARE THE PROPERTY OF CYNTEC CO., LTD.
AND SHALL NOT BE REPRODUCED OR USED AS THE BASIS FOR THE
MANUFACTURE OR SALE OF APPARATUS OR DEVICES WITHOUT PERMISSION
CYNTEC CO., LTD.
6-2 Mechanical
Item
Specification and Requirement
Test Method
Solderability
The surface of terminal immersed
shall be minimum of 95% covered
with a new coating of solder
Solder bath :
After immersing in flux, dip in
2455
molten solder bath for
20.5 seconds
Resistance to Solder
Heat
R:
(1.0%+ 0.05)
Without distinct deformation in
appearance
(1) Pre-heat : 100~110
for 30 seconds
(2) Immersed at solder bath
of 2705
for 10
1 seconds
(3) Measuring resistance
1 hour after test
Vibration
R:
(0.5%+ 0.05)
Without mechanical damage such as
break
(1) Vibration frequency :
( 10Hz to 55Hz to10Hz ) in 60
seconds as a period
(2) Vibration time :
period cycled for 2 hours in each
of 3 mutual perpendicular
directions
(3) Amplitude : 1.5mm
Shock
R:
(0.25%+ 0.05)
Without mechanical damage such as
break
(1) Peak value : 490N
(2) Duration of pulse : 11ms
(3) 3 times in each positive
and negative direction of
3 mutual perpendicular
directions
Bending Test
R:
(1.0%+ 0.05)
Without mechanical damage such as
break
Bending value : 3 mm for
301 seconds
PAGE 5 OF 9
TITLE :
The Engineering Spec. For RS062R-XXXX-X2N
DOCUMENT
NO.
CYNP-5X-001
PAGE
REV.
A0
UNLESS OTHERWISE SPECIFIED
TOLERANCES ON
X =
X.X =
X.XX =
ANGLES
HOLE DIA.
SCALE
X
UNIT
X
APPROVED BY
DRAWN BY
2005-10-04
DESIGNED BY
CHECKED BY
THIS DRAWINGS AND SPECIFICATIONS ARE THE PROPERTY OF CYNTEC CO., LTD.
AND SHALL NOT BE REPRODUCED OR USED AS THE BASIS FOR THE
MANUFACTURE OR SALE OF APPARATUS OR DEVICES WITHOUT PERMISSION
CYNTEC CO., LTD.
6-3 Endurance
Item
Specification and Requirement
Test Method
Rapid change of
Temperature
R:
(1.0%+ 0.05)
Without distinct damage in
appearance
(1) Repeat 5 cycle as follow :
(-553
,30minutes)
(Room
temperature, 2~3 minutes)
(+1252
,30minutes)
(Room temperature, 2~3
minutes)
(2) Measuring resistance
1 hour after test
Moisture with Load
R:
(3.0%+ 0.1)
Without distinct damage in
appearance
Marking should be legible
(1) Environment condition :
402
,90~95
% RH
(2) Applied Voltage :
Rated voltage
(3) Test period : (1.5 hour ON)
(0.5 hour OFF) cycled for
total 1,000 + 48 / - 0 hours
(4) Measuring resistance
1 hour after test
Load Life
R:
(3.0%+ 0.1)
Without distinct damage in appearance
(1) Test temperature :
702
(2) Applied Voltage : rated voltage
(3) Test period : (1.5 hour ON)
(0.5 hour OFF) cycled for
total 1,000 + 48 / - 0 hours
(4) Measuring resistance
1 hour after test
Low Temperature
Store
R:
(3.0%+ 0.1)
Without distinct damage in appearance
(1) Store temperature :
-553 for total
1,000 + 48 / - 0 hours
(2) Measuring resistance
1 hour after test
High Temperature
Store
R:
(3.0%+ 0.1)
Without distinct damage in appearance
(1) Store temperature :
+1252
for total
1,000 + 48 / - 0 hours
(2) Measuring resistance
1 hour after test
PAGE 6 OF 9
TITLE :
The Engineering Spec. For RS062R-XXXX-X2N
DOCUMENT
NO.
CYNP-5X-001
PAGE
REV.
A0
UNLESS OTHERWISE SPECIFIED
TOLERANCES ON
X =
X.X =
X.XX =
ANGLES
HOLE DIA.
SCALE
X
UNIT
X
APPROVED BY
DRAWN BY
2005-10-04
DESIGNED BY
CHECKED BY
THIS DRAWINGS AND SPECIFICATIONS ARE THE PROPERTY OF CYNTEC CO., LTD.
AND SHALL NOT BE REPRODUCED OR USED AS THE BASIS FOR THE
MANUFACTURE OR SALE OF APPARATUS OR DEVICES WITHOUT PERMISSION
CYNTEC CO., LTD.
7. Recommend Land Pattern Dimensions
A
0.30
B
0.30
P
0.50
C
0.9
Unit : mm
C
B
P
A
PAGE 7 OF 9
TITLE :
The Engineering Spec. For RS062R-XXXX-X2N
DOCUMENT
NO.
CYNP-5X-001
PAGE
REV.
A0
UNLESS OTHERWISE SPECIFIED
TOLERANCES ON
X =
X.X =
X.XX =
ANGLES
HOLE DIA.
SCALE
X
UNIT
X
APPROVED BY
DRAWN BY
2005-10-04
DESIGNED BY
CHECKED BY
THIS DRAWINGS AND SPECIFICATIONS ARE THE PROPERTY OF CYNTEC CO., LTD.
AND SHALL NOT BE REPRODUCED OR USED AS THE BASIS FOR THE
MANUFACTURE OR SALE OF APPARATUS OR DEVICES WITHOUT PERMISSION
CYNTEC CO., LTD.
8. Packaging
8-1 Dimensions
8-1-1 Tape packaging dimensions
8-1-2 Reel dimensions
2.0 0.5
13.0 0.5
20min.
9.0 0.3
Unit : mm
1
7
8


2
.
0
6
0
.
0


2
.
0
5
6
.
0


2
.
0
11.4 1.0
Code
Dimensions (mm)
A
0.70 0.10
B
0.90 0.10
W
8.0 0.3
C
1.75 0.1
D
3.5 0.05
P0
4.0 0.1
P1
2.0 0.05
P2
2.0 0.05
T
0.5 0.1
t
0.43 0.05
D0
1.5
+0.1
-
0.0
Sprocket hole
W
t
P0
P2
D0
Carrier cavity
T
A
B
P1
Pulling direction
D
C
PAGE 8 OF 9
TITLE :
The Engineering Spec. For RS062R-XXXX-X2N
DOCUMENT
NO.
CYNP-5X-001
PAGE
REV.
A0
UNLESS OTHERWISE SPECIFIED
TOLERANCES ON
X =
X.X =
X.XX =
ANGLES
HOLE DIA.
SCALE
X
UNIT
X
APPROVED BY
DRAWN BY
2005-10-04
DESIGNED BY
CHECKED BY
THIS DRAWINGS AND SPECIFICATIONS ARE THE PROPERTY OF CYNTEC CO., LTD.
AND SHALL NOT BE REPRODUCED OR USED AS THE BASIS FOR THE
MANUFACTURE OR SALE OF APPARATUS OR DEVICES WITHOUT PERMISSION
CYNTEC CO., LTD.
8-2 Peel force of top cover tape
The peel speed shall be about 300 mm/minute
The peel force of top cover tape shall be between 0.1 to 0.7 N
8-3 Numbers of taping
10,000 pieces/reel
8-4 Label marking
The following items shall be marked on the production and shipping
Label on the reel.
8-4-1 Production Label
(1) Part No.
(2) Description
(3) Quantity
(4) Taping No.
8-4-2 Shipping Label
(1) *Customer's name
(2) *Customer's part No.
(3) Manufacturer's part No.
(4) Manufacturer's name
(5) Manufacturer's country
*Note : Item (1) and (2) are listed by request
165 ~ 180
Top Cover Tape
0.1~0.7 N
PAGE 9 OF 9
TITLE :
The Engineering Spec. For RS062R-XXXX-X2N
DOCUMENT
NO.
CYNP-5X-001
PAGE
REV.
A0
UNLESS OTHERWISE SPECIFIED
TOLERANCES ON
X =
X.X =
X.XX =
ANGLES
HOLE DIA.
SCALE
X
UNIT
X
APPROVED BY
DRAWN BY
2005-10-04
DESIGNED BY
CHECKED BY
THIS DRAWINGS AND SPECIFICATIONS ARE THE PROPERTY OF CYNTEC CO., LTD.
AND SHALL NOT BE REPRODUCED OR USED AS THE BASIS FOR THE
MANUFACTURE OR SALE OF APPARATUS OR DEVICES WITHOUT PERMISSION
CYNTEC CO., LTD.
9. Care note
9-1 Care note for storage
(1) Resistor network shall be stored in a room where temperature and humidity must be controlled.
(temperature 5 to 35
, humidity 45 to 85% RH) However, a humidity keep it low, as it is
possible.
(2) Resistor network shall be stored as direct sunshine doesn't hit on it.
(3) Resistor network shall be stored with no moisture, dust, a material that will make solderability
inferior, and a harmful gas (Chloridation hydrogen, sulfurous acid gas, and sulfuration
hydrogen)
9-2 Care note for operating and handling
(1) It is necessary to protect the edge and protection coat of resistors from mechanical stress.
(2) Handle with care when printing circuit board (PCB) is divided or fixed on support body,
because bending of printing circuit board (PCB) mounting will make mechanical stress for
resistors.
(3) Resistors shall be used with in rated range shown in specification. Especially, if voltage more
than specified value will be loaded to resistor, there is a case it will make damage for machine
because of temperature rise depending on generating of heat, and increase resistance value or
breaks.
(4) In case that resistor is loaded a rated voltage, it is necessary to confirms temperature of a
resistor and to reduce a load power according to load reduction curve, because a temperature
rise of a resistor depends on influence of heat from mounting density and neighboring element.
(5) Observe Limiting element voltage and maximum overload voltage specified in each
specification
(6) If there is possibility that a large voltage (pulse voltage, shock voltage) charge to resistor, it is
necessary that operating condition shall be set up before use.
© 2019 • ChipFind
Контакты
Главная страница